Home > ELECTRICAL > ROUGH ELECTRICAL > ELECTRICAL BOXES
Choose a sub category:
OUTLET BOXES PVC SWITCH BOXES UTILITY BOXES
OCTAGON BOXES CEILING BOXES BOX COVERS
ELEC BOX SUPPORTS SPECIALTY BOXES
Sort By:
1 2 3 ... 7
Thomas & Betts B118A Switch Box Thomas & Betts B120A-UPC Switch Box Thomas & Betts B122A-UPC Wall Box
With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. With captive nails. Four integral clamps, two each end. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies.
Hubbell 860 Raised Blank Utility Box Cover Hubbell 864 Utility Box Cover Carlon HB1BL Blank Handy Box Cover
Steel box cover, blank with no knockouts. 2-5/16" wide x 4-3/16" tall. UL Listed. Steel box cover for duplex receptacle. Rugged construction. 2-5/16" wide x 4-3/16" tall. UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 1/2" knockout. 4.3" length x 2.38" width. UL Listed.
Carlon HB1GF Handy Outlet Box Cover Carlon HB1SW Handy Box Cover Hubbell 722 Octagon Flat Blank Electrical Box Cover
Made of a durable polycarbonate material that is virtually indestructible. 4.3" x 2.38". UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 4.3 length x 2.38 width. UL Listed. Rugged construction, used to close an outlet box. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed.
Hubbell 8752 Square Flat Blank Electrical Box Cover Hubbell 865 Utility Box Cover Carlon HB1DP Handy Box Cover
Rugged construction, used to close an outlet box. 4" square. Angled mounting slots allow for correction of box misalignment. UPC bar code. UL Listed. Steel box cover with single toggle switch opening in the center. 2-5/16" wide x 4-3/16" tall. UL Listed. Made of a durable polycarbonate material that is virtually indestructible. 4.3" length x 2.38" width. UL Listed.
Thomas & Betts BH122A-UPC Outlet Box Raco 8977 Electrical Box Supports Hubbell 863 Utility Box Cover
Lightweight design and durable plastic. Listed for masonry walls. Safe to install and will never rust or corrode. Includes nails for quick, easy installation. 22 cubic inch rigid wall. 3-7/8" x 2-3/8" x 3-3/4". UL Listed. Use two to mount switch box with plaster ears to hollow wall. Slips between box and wall, tabs bend inside box. Steel box cover with single 1.406" receptacle opening in the center. Rugged construction. 2-5/16" wide x 4-3/16" tall. UL Listed.
Carlon B112HB Handy Box Thomas & Betts B114R-UPC Switch Box Hubbell 703 Round Flat Ceiling Pan Cover
PVC handy box used for many wiring applications. Weather-resistant and nonconductive. Will accept metal handy box covers or nonmetallic covers. Includes hardware for quick, easy installation. Old work wall case. Safe, non-conductive. Two Zip-Mount retainers. Four integral clamps, two each end; mounting ears. 14 cubic inch,  2-3/4" x 2-1/4" x 4-1/8". UL Listed. Steel box cover with 1/2" knockout in the center. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed.
Hubbell 724 Octagon Flat Electrical Box Cover Hubbell 8753 Square Flat Electrical Box Cover Hubbell 8772 Square Raised Device Box Cover
Steel box cover with single 1/2" knockout in the center. Key hole mounting feature allows for installation of cover without removing box screws. UL Listed. Steel box cover with single 1/2" knockout in the center. 4" square. Angled mounting slots allow for correction of box misalignment. UL Listed. Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed.
Hubbell 8660 Utility Box Hubbell 861 Utility Box Cover Thomas & Betts B232A-UPC Outlet Box
Used for convenience outlets, switch boxes or small junction boxes. Drawn construction and raised grounding provision. Acceptable for use in 2-hour rated walls. Six 1/2" knockouts (sides). Two 1/2" knockouts (ends). Two 1/2" knockouts (bottom). 4" x 2" x 1-7/8" deep. 13.0 cubic inch capacity. UL Listed. Steel box cover with 1/2" knockout in the center. 2-5/16" wide x 4-3/16" tall. UL Listed. New work safe, non-conductive. With captive nails. Eight integral clamps, four each side. 32 cubic inches. Meets NEMA OS-2, UL Listed, classified for fire wall assemblies. 3" depth x 4" x 3-3/4".
Thomas & Betts B520A-UPC Ceiling Box Carlon E460R-CAR Blank Round Outlet Box Cover Raco 8768 Mud-Ring Raised Square Electrical Box Cover
With captive nails. 3/0 - 4/0 combination. Fixture spacing for 2-3/4" - 3", 6 integral clamps. 4" diameter non-metallic ceiling box, 20 cubic inch volume. Listed for fixture support up to 50 lb. 4" diameter x 2-1/4" depth. Meets NEMA OS-2, UL Listed. RoHS Compliance. High impact lightweight round blank PVC cover for 4" round boxes to make junctions. UL Listed. Used to close outlet box. For mounting switch or receptacle. Size 4" x 4",steel, UL Listed.
Hubbell 8192 Outlet Box Carlon A410R-CAR Square Electrical Box Cover Raco 871 Wall Plate
Conduit wiring system. Installed in ceilings or walls for lighting fixtures, switches or receptacles. Used where multiple conductor runs are split into two or more directions to bring power to a number of electrical devices. Drawn construction and raised grounding provision for surface mount applications in ceilings or walls for lighting fixtures or receptacles. Eight 1/2"and four 3/4" conduit knockouts (sides). Two 1/2" and two 3/4" conduit knockouts (bottom). 4" square x 1-1/2" deep - 21.0 cubic inches. Acceptable for use in 2-hour rated fire walls. UL Listed. UPC bar code. Suitable for tile, plaster, sheetrock, paneling, masonry and all wall coverings. Brilliant electric blue. UL Listed. Two device switch box cover. Made from unpainted, pregalvanized steel. Used with  2 toggle 2 gang switch boxes. UL 514-A Listed, File E195978 / CSA Listed, File LR-1082.
   
 
1 2 3 ... 7